192.168.1.1 Router admin login - Default D-Link & Netgear access

192.168.1.1 Admin Login | 192.168.l.l Default Router Login

August 25, 2019 by Sidonia

If you’re installing the router for your Home or Office for the first time, then you have to know some network related terms. A router is one of the most used networking devices, and every Router has its default IP address. It is either 192.168.1.1 or 192.168.0.1 or 192.168.254.1, 192.168.254.254 etc. Now if you want to Setup Router, you have to log in to your Router. But it required username and password to log in. When you haven’t logged in to your router with 192.168.11 IP Address for quite a while, it’s simple to forget your username or password.

More than four billion IPv4 addresses are there, some are easy to remember but most of them just make knots in one’s brain. Sooner than you expect, one specific router IP address will definitely catch your attention as most of the Linksys routers use it as their default IP address. Present article exhaustively covers all that you want and need to know regarding it. And this omnipresent IP address is none other than 192.168.1.1,

What Is So Special About IP Address 192.168.1.1?

Any device, as most of computer literates know, which is attached to any computer network which makes use of the Internet Protocol for communicating, is provided with a unique numerical identity or an Internet Protocol address which is commonly called IP address. An IP address provides a unique identity to each and every connected device for establishing a specific path to reach or access it.

In the event the router is still not working after a 30-30-30 reset it may be that it’s broken and you should think about obtaining a new unit or sending your present one in for repairs. Before starting to get the key, you might have to connect it to the routers or modem by utilizing an Ethernet wire.

192.168.1.1 Admin Login – Default Router Login

If you cannot access your router, it might be for few explanations. Every router includes default username and password which you could change based on your requirements.

It comes with default login detail what you have to use to login to the router. So, you’re able to learn about that router before purchasing the gadget. Now many routers have the USB cable.

There are certain restrictions on accessibility to IP addresses through the public internet The IP address 192.168.1.1 is among those which belong to restricted category. It is one of the 65,536 IP addresses belonging to16-bit block of the private IPv4 address spectrum including addresses starting all the way from 192.168.0.0 up to 192.168.255.255. Most of the Linksys routers have this as their default IP address.

Local area networks (LANs) make use of Private IP addresses and were defined in order to defer the exhaustion of IPv4 addresses. No prior approval from a regional Internet registry is necessary for using private IP addresses which makes it possible for any user ranging from a private home user to any big organization to easily set up devices connected through internet using a method called NAT or Network Address Translation, which makes it possible to assign a public address to a computer within a private network.
As a default gateway, home router manufacturers use private IP addresses, among them 192.168.1.1 is included, making it possible for the users to access the router admin panel by just typing http://192.168.1.1 into a web browser to make any changes to router settings as desired.

How to Login to 192.168.1.1 IP TP-Link Router

Step 1: Connect your Router and Your PC with cable (RJ45).

Step 2: First open your Browser and type 192.168.1.1 in the URL Bar. Press Enter.

Step 3: Now it will ask for username and password. Note that every Router has different username and password. Here we are going to share a list of all the Router username and password.

Google Drive Link – https://goo.gl/uYejjx
Download File – https://goo.gl/eS1saS

Step 4: Find your Router and its login details.

Most common username and password are:

Username: admin
Password: pass/admin

Step 5: Once, logged in, go to wireless settings and change settings.

If you wish to use the internet at an affordable speed, then Wi-Fi is the ideal option. After some time you’re linked to the web. If the internet isn’t showing as connected, you should talk to your ISP to make certain your router is configured correctly to access the modem. Using the web and using the internet browser became almost synonymous.

How to Login To Linksys Router using 192.168.l.l

Linksys Routers have 192.168.1.1 IP as a default IP address. You can easily login into the Linksys Router with www.192.168.1.1.com IP address. Now follow the steps to access Linksys Router Admin.

Step 1: Open any Browser on your computer and then type http://192..168.1.1.

Step 2: It will ask username and password. Enter default username and password which is admin-admin or admin-pass.

Username: admin
Password: pass/admin

Step 3: Once done, you can access Router admin page.

Step 4: You can change router password from Settings.

How To Login to Netgear Router 192.168.l.l

Step 1: Connect Netgear router with PC > open Browser and type 192.168.1.1 > Enter.

Step 2: Enter default username and password as mentioned above. Go to Wireless Settings and customize settings.

To connect any device to the net, you require a 192.168.1.1 Login IP address. In reality, an address is seen as private if it’s within an address span that is reserved for private use. 192.168.1.1 IP address will help to connect different devices to it. When you would like to change the IP address, then you’ve got to think about the IP class. It is very important to pick a dynamic or static IP address.

For every 192.168.1.1 IP router, you will secure the username and password right at the rear of the router and if you don’t remember your password by mistakenly then you’ve got to reset your router. Assigning an administrator password doesn’t impact communication to the web. If you don’t remember your password, all you need to do is to reset your device. Some could call for a username and a router password to observe the settings; others will just demonstrate a message if you’re on the net.

There are multiple companies making wireless routers out there, although most of times all you have to do is just connect with your ISP using router ip address. Options are available in settings of router menu once you logged in such as security options WPA2 or WEP and more. If you ISP require username and password each time you start your internet then you need to select option PPPOE which will make sure it won’t ask you id and password.

If you don’t remember your password, you want to reset your modem. Next, you might use the default password that’s given in the post. Login, you ought to keep in mind the password for the very same in case if you’ve changed previously. If you prefer to change the wifi password for 168.192.1.1.

Even if one has changed the default password to a different one and has forgotten it there is no need to panic. By pressing and holding the “RESET” button of the router for 10 seconds after restarting it, one can restore the router to its default factory settings along with the original password

The blinking of the Power LED of the router is to be ensured when one presses the “RESET” button of the router, which in turn will ensure that the router is being properly reset. Although the reset button position on the router varies from one model to the other, usually it is located right next to the power input connector.

By using the router setup page also, one can alternatively reset one’s router to its default factory settings:

IP Address 192.168.1.1 Router Reset Settings

Step 1. Switch the router on and with an Ethernet cable, connect it to the computer.

Step 2. After opening the desired web browser type “http://192.168.1.1” into the space provided in the address bar.
Step 3. Key in the exact router login and correct password combination in the provided spaces.

Step 4. After clicking the Administration tab, click on the “Factory Defaults” sub-tab.

Step 5. Click the “Restore Factory Defaults” button provided under the section “Factory Defaults.”

When setting up router – you must have questions. Here are the some most asked questions with their answers.

192.168.1.1 Router Login FAQ :

What to do if the router has another address in the network?

If you cannot log on to 192.168.0.1 in the router’s personal cabinet, flip it over and see which address is on the label and whether it matches what you enter. If there is a hostname like tplinkwifi.net or tplinklogin.net, then try to go through it.

How to make proxy setting for the router?

Open the application settings:
We are looking for the section “Network”. In it there will be a button “Change proxy server settings”.
Click on it and get into the properties of the Internet browser Windows 10. We need the “Connections” tab:
We press the button “Network settings”. In the next window, you’ll need to check “Use a proxy server for local connections”:
It’s worth it – boldly remove it and click on the “OK” button. Try again to enter the web interface modem or router.

How one can verify the web browser for the router setup?

First, check the properties of the Windows Explorer – again, go back to the Windows Management Console -> section << Network and Internet >>:
We find the link << Internet Options >>, and then – select the << Connections >> tab where you need to click the ‘Network Settings’ button.

What should be focused on while configuring a router for the first time?

Entering the router for its configuration is carried out strictly according to a specific IP address, different for each manufacturer. The most common login addresses are 192.168.0.1 and 192.168.1.1, and the user’s login / password is admin-admin or admin-password.

How to enter a router by IP 192.168.0.1?

Each router is a device whose task is to get the Internet from one segment of the network (your provider) and distribute it to another segment (your home network). Therefore, the router always has several network interfaces. Home-type routers of the initial type usually have 5 ports, 1 of which is intended for connection to an Internet provider (WAN), and the remaining 4 for connecting computers or other devices on the local network (LAN).

99.9% of the routers are managed through the web interface, so you must enter the router settings through any web browser using a specific address. Usually this is http://192.168.0.1 or http://192.168.1.1.

How do I find the IP pages for logging into the router?

The standard name and password for entering the settings are also indicated there. The picture below shows the IP address 192.168.0.1 and the standard name and password ( admin – admin )
To enter the web interface, you need to turn on the router and connect it to a computer or laptop using a patch cord (usually it comes bundled). One end you plug into the socket for the network card on your computer, the other in the LAN jack on the router. It is important to know that WAN and LAN connectors are usually different in color and LAN connectors are always larger than WAN.
That needs to be inserted into the LAN connectors. If you do not know which IP to go to the router, you can see in the properties of the network connection.
By default, each router is automatically allocated IP addresses. To find out what interests us, type WIN + R, drive cmd, and then OK. A command line opens where we enter the ipconfig command and press ENTER.
We are interested in the Default Gateway parameter. It is for this IP address and it is necessary to enter the settings of your router.
We open any browser and drive into the address line IP 192.168.1.1 or 192.168.0.1 – depends on the specific router.

I was able to go to 192.168.0.1 / 192.168.1.1 and what’s next?

Next, you need to configure your router, in accordance with the parameters issued by the provider. First you need to go to the WAN or Internet section.
In the WAN section of the router, the type of connection to the provider is usually configured, for example, VPN, L2tP, or PPoE. The website of your provider usually has Internet connection settings for the most common router models. I propose to do by analogy.
You do not need to touch the LAN section. There are parameters of a local network, distribution by a router of IP addresses, etc.
Section WIRELESS or wireless network. We configure here the parameters of your home Wi-FI network, name, password, etc.

I cannot log on to 192.168.0.1.what to do?

Check if your computer has a cable connected to the router. Rewind the patchcord, make sure that the corresponding LAN port indicator on the router is lit. The light should be flashing, which means that data is exchanged between the router and the PC.
Check the network settings. It is possible that the DHCP server is disabled in the router and the distribution of IP addresses in the automatic mode is not performed by them.

What IP address can be used if we have not idea about what type of IP is used on your router – 192.168.0.1, 192.168.1.1 or another?

If you do not know what type of IP is used on your router – 192.168.0.1, 192.168.1.1 or another – you can use the hint that the manufacturer left for users in the form of a sticker. You can find it on the body behind or below. As you know that the D-Link router uses 192.168.0.1 login admin, the password is admin.

The page does not open for Login 192.168.0.1 or 192.168.1.1. What to do ?

Try another web browser. Often we have to deal with the fact that due to a malfunction or a crooked cache from a web browser, we cannot go to the router. Try cleaning the cache and cookies. It does not help – use another browser. As practice shows, the best way to access the settings of network devices through 192.168.0.1 is suitable for Internet Explorer and Microsoft Edge. You can also try to make an attempt to log in using secure browser mode.

How to check if the router is available on 192.168.0.1?

To do this, you need to “ping” the device. Run the test command: ping 192.168.0.1.
Press the button << Start >> and select the item << Execute >>. If you have Windows 8 or 8.1, you just need to press the win + r key combination.
In the opened window type the command: ping 192.168.0.1
You have a modem or a router with multiple LAN ports – try to include the cable in each of them in turn and start the ping.
If the router pings perfectly and without losses: go to step 3.

How to fix the issue of “unidentified network”?

You need to manually register the IP address in the network connection settings on the computer.
A list of all network connections opens. If one of them says “Unidentified network “, it means that the IP address was not assigned. It is because of this that you cannot get into the personal cabinet of the router. You need to right-click on this connection and go to Properties.
Select the Internet Protocol version 4 mouse and click the Properties button again.
Here it is necessary to register the IP address of the computer in accordance with the typical settings of the routers of this brand. The IP address of the computer is ALWAYS different from the router’s IP address. The last digit in the IP address of the router in 99% of cases is 1.

What should I do if 192.168.1.1 does not open (not available)?

One possible error may be a problem with the browser, if the device detects the connected router. You must install a different browser and repeat the menu entry action. If this does not help, you need to check the browser for viruses and unwanted extensions.
The next error, the antivirus blocking of the network address. It is solved by disabling the firewall (defender against unwanted network traffic) for a while, or by adding a network address to the list of secure sites. Standard Windows firewall is disabled in the following way: the control panel – the system and the security – the firewall – disabling the defender windows. It is worth noting that this error is very rare.

How to find out the login and password for the input 192.168.1.1?

As mentioned above, the standard password and login is the word “admin”. Sometimes it can be a combination of words, where the login is admin, and the password is password. Most manufacturers point to the back side: the network address, the menu access data that is set by default.

What to do if the standard login / password (admin admin) does not match?

You need to check the layout and correctness of data entry, then try changing the browser or the device through which you are logged on. If all these actions do not help, then you have to reset the settings to standard settings. In the back of the device there is a hole, which with the help of something thin (a clip or a needle) must be clamped for 10 or more seconds. After that, everything will return to the factory settings and you can enter the menu.

How to set or change the password 192.168.1.1?

So, after successfully logging into the menu, you need to find the Wireless-security section, here you need to choose WPA2-Personal protection and set the password that suits you, saving the changes.

One must, however, note that, the need to enter the correct router login/password combination makes the alternative method of resetting the router to the default factory settings redundant for such scenarios where one has forgotten the correct password.

To Conclude…

You are now equipped with the knowledge of what the IP address 192.168.1.1 is and how to use it for logging into the routers which utilize it as the default gateway for entry. Its admin panel is now open to your exploring and you can alter various settings to add to the safety and speed of your network.

Thanks for reading this article regarding 192.168.1.1 IP Login and How to Login into 192.168.1.1 Router. If you need any help then comment down.

10.0.0.2 IP address Login- Telkom, D-Link Router Access

August 23, 2019 by Sidonia

What is the 10.0.0.2 IP address? Where is it used, and why?

The IP address 10.0.0.2 is used by several private business networks. Popular Router selling Brands, such as Edimax, Siemens, Micronet and several other brands use the 10.0.0.2 IP address as their default gateways. The primary reason for using this IP address inside a private network is for the ease of communication.

10.0.0.1 IP Address vs 10.0.0.2 IP Address

The answer to the above question can be understood in this way- “since a business network is very large in size, the routers that these business places use generally have the 10.0.0.1 IP address as their default gateway login, but all these routers are configured in such a manner that there is a subnet in them which supports a client IP address begining with 10.0.0.2”. This means that the default IP address 10.0.0.1 is subjected to the process of ‘subnetting’, where the created subnet has its IP address starting from 10.0.0.2 in order to provide flexibility to the business companies so that they can allocate a large number of IP addresses within their organisations.

To make you understand things in a better way, let me explain you the meaning of a subnet. An IP network can be subdivided into two or more than two networks, creating subnetworks. Whereas, the process of subdivision of the “Host Identifier” into sub parts is called subnetting.

Thus, this “main IP address” division process creates the required number of subnets, with each subnet using a different IP address altogether, to make the ‘IP address allocation’ process easier for these private business companies.

Which devices use the 10.0.0.2 IP address?

The 10.0.0.1 IP address is assigned to various devices such as :

MODEMS
ROUTERS
IOT (INTERNET DEVICES) DEVICES SUCH AS :-

(a.) SMART SPEAKERS (b.) RASPBERRY PI (c.) WEB CAMERAS

Uses of the 10.0.0.2 router login:-

There are a number of uses of the 10.0.0.2 router login. These are discussed as under :-

IP QoS :- IP QoS stands for “Quality of service in IP networks”. It is designed to reduce the impact caused when the connection is under heavy load. Using IP QoS, a specific minimum or maximum bandwidth can be assigned for each computer, which means they will have lesser impact on each other.
DNS and Proxy Settings:- DNS stands for “Domain Name System”. DNS is a system of conversion of alphabetic names into numeric IP addresses. The DNS system could be understood by this observation: When the web address (also known as URL) is typed in the address bar of an internet browser, the DNS servers return the IP address of the Web server associated with that name. For example: the domain name www.example.com will be translated to the IP address 198.105.232.4. Whereas; A Proxy server is a server that acts as an intermediary for requests from clients seeking resources from other servers.
WPS:- WPS stands for “Wi-Fi Protected Setup”. WPS is a network security standard which creates a secure wireless home network. It allows home users, who don’t know much about network security options to set up a Wi-Fi protected access, so that their Wi-Fi networks could be secured.
MAC Address:- MAC Address stands for “media access control address”. MAC Address of a device is a unique identifier assigned to a “network interface controller”(NIC). For communications within a network segment, it is used as a network address.
LAN, WAN and WLAN settings:- LAN, WAN and WLAN stands for “Local area network”, “wide area network” and “wireless local area network”. The 10.0.0.2 DNS can be used for setting the security settings in these area based networks.
DHCP: DHCP stands for “Dynamic host configuration protocol”. A DHCP server assigns an IP address and other network configuration parameters to each device on a network so that they can communicate with other IP networks.
PPPoE: PPPoE stands for “Point-to-Point over Ethernet”. PPPoE is a means of connecting DSL-modems to an Ethernet-only router.

Login to your Telkom Router admin page

Step 1: Open your Internet browser. In the address bar of your browser, type https://10.0.0.2 and press enter.[Make sure you don’t type 10.0.0.0.2 because typing this wrong IP address in the address bar is going to land you up with a list of search results only, and not the login page.]

Step 2: Now you must see the login page, which is a gateway to the admin dashboard of your Telkom router. Enter your router’s default Password in the password field. There is no default Username for Telkom routers, so you don’t need to enter anything. Now, press the login button.

*For your Telkom router, the default Username is “blank(nothing)” and the default Password is “admin”.

*In case the default Username and Password has been changed previously by you, and the new Username and Password has been forgotten, then you need to reset the router.

Step 3: Now you will enter the admin dashboard of your Telkom router, where you will get access to various router settings. You can perform the following tasks:-

CHANGE THE SSID: SSID stands for “service set identifier”. It is a sequence of characters that uniquely names a wireless local area network. Its is required to change the SSID, so that someone cannot guess and enter your router settings.
UPDATE SECURITY SETTINGS: Wi-Fi Protected Access 2, also known as WPA2, is a commonly used network security technology used on wireless routers.WPA2 should always be used to secure our wireless network.

Steps to reset your router:-

Step 1: Locate the word reset written at the back of your router.

Step 2: Take a toothpick, or a paperclip, or a pin and insert it in the reset button hole, and keep holding for 10-15 seconds, until the router is fully reset and is powered back on.

Step 3: The router will be reset back to its original default settings. Now type the IP address 10.0.0.1 in your web browser and type the default Username and Password in the login page. you will be able to access the admin dashboard successfully.

Steps to change the D-Link router password:-

Step 1: Open your Internet browser. In the address bar of your browser, type https://192.168.0.1 and press enter.[Make sure you don’t type 192.168.0.0.1 because typing the wrong IP address like this in the address bar is going to land you up with a list of search results only, and not the login page.]

Step 2: Now you must see the D-Link router login page, which is a gateway to the admin dashboard of your D-Link router. Enter your router’s default Username in the Username field. There is no default password for your D-Link router, so you don’t need to fill anything in the password field. Now, press the login button to enter the admin dashboard.

*For your D-Link router, the default Username is “admin” and the default Password is “blank(nothing)”.

*In case the default Username and Password has been changed previously by you, and the new Username and Password has been forgotten, then you need to reset your D-Link router.

Step 3: Now you will enter the admin dashboard of your D-Link router. [Click on the tools tab-> then under the admin password section, enter the new password->then verify your password-> then click on the save settings button]

Step 4: You may need to reboot your D-Link router, to save the newly formed router password. The next time you will login by entering 192.168.0.1 in your browser’s address bar, you will be able to enter the Admin dashboard by entering the username and your new password.

Thanks for reading this article, Hope I was able to resolve all of your problems!

192.168.0.1 Admin Login – Router Default Access

August 22, 2019 by Sidonia

192.168.0.1 is an integral part of the Internet Protocol version 4 network and is a 16-bit address type that is used by several router manufacturers. There are several addresses in this range, such as 192.168.1.1 and 10.0.0.1 and all of them are private IP addresses that various router and modem manufacturers use to direct their traffic. Users with experience in configuring a router should have heard of or come across IP addresses like 192.168.1.1 and 10.0.0.0.1. If not, don’t worry about it because this article will tell you everything you need to know about 192.168.0.1 and its associated admin login procedure.

Routers manufacturers of the likes of D-Link, Linksys, and TP-Link use 192.168.0.1 for their default admin portal and hence if you use these routers, this is an important IP address for you. Private IP addresses all refer to the same network and can therefore, be used as an effective way to resolve router conflict or IP address conflict easily. Users can utilize such private IP addresses to log in to their router and configure their device. Such addresses have the power to connect to multiple routers, making them a useful tool for managing the server or network. http://dlinkrouter.local or http://192.168.0.1 can be accessed.

Users can manage their network settings from this admin page without fearing an intrusion or privacy attack. Manufacturers use several IP addresses to provide their clients with a simple tool to manage and edit their wireless and LAN network settings.

Be certain your password is strong. Then you need to enter a username and password for 192.168.01 Router. You’ll be prompted to put in a password or passphrase. There are some ways to find your IP address. It helps to connect other devices to it. It is the basic unit of every internet network connection. The IP address ought to be correctly formatted whatever you would like to do.

Connecting to your 192.168.0.1 router is very simple, all you have to do is, Open your internet browser and compose the default IP address there. The user should work with the ping and 192.168.0.1 IP when it is vital for testing the link between the computer and router. Such a password is quite strong, and it is extremely hard to break. Such password is quite tricky to hack. Modifying the password frequently is the most suitable choice. You can alter the router password.

What can you Use 192.168.0.1 for?

Change Wireless settings
Create new Dial-Up connection
Create new DSL connections.
Improve security settings
Validate SSID settings
Update network’s name
Change username and password
Set-up and configure DNS
Change wireless password.
Set up a new port for gaming or any other purpose

How to Login 192.168.0.1 Router

Connect your router to your device.
This can be done using either an Ethernet cable or through a wireless network set-up.
A wired connection works better as it reduces chances of the connection failing or getting disconnected. Problems usually arise when the connection gets logged out before you click Save, and this deletes any changes you made. When this happens, you will have to re-configure your net and then make the changes again after logging in.
Always opt for a cable connection as this is more secure and robust.
Turn both your device and the router on.
Open your favourite browser.
Enter https://192.168.0.1 into your address bar, which is located on top of the browser and press enter.
Once you reach the login page, enter your credentials when it asks for username and password.
Once you are inside the network page, make the required changes.
Click Save to apply the changes you have made.

192.168.0.1 Default Credentials to Login into Router

Most new routers make use of default login credentials to access their respective login or admin page. These credentials are set by the manufacturer and can be found on the back of the router. Certain manufacturers also add a data-sheet in the router box to allow users to find their default settings. If neither of these plans work, you can always try googling your router name + default login to gain some insight on what your credentials are. Here’s a look at some of the most common default login details that major companies use. Try some of these if you can’t find your default login details anywhere else.

admin / admin
admin / PASSWORD
admin / password
admin / none
Admin / blank
none / none
none / admin
admin / blank
Root/none
Root/password
Root/High-speed
Root/W2402

How to Resetting the Router 192.168.o.1

If you forgot your credentials, you can always try the default ones but in case you forgot the credentials you created, reset your router. To do so, press and hold the reset button for over 10 seconds or till you see the router LED blink, whichever occurs first. This blinking indicates that the router is being reset to factory settings. Once the reset is completed, the router will go back to its default credentials, and so you can access the admin page using the credentials your manufacturer had initially set.

How to Find your Router IP Address

Open Command Prompt and then type ‘ip config‘ command. Here you can see Router IP address.

For people using Windows users, go to your Command Prompt and type ipconfig to see details regarding your default IP address.
MAC users should go to Apple Menu>>System preferences>>Network Tab>>Network Connection>>Advance>>TCP/IP. You will then see your IP address near the right-hand side of the screen.
Linux or Unix users must go to Terminal>>Applications>>System Tools>>Terminal and then use command IP course | grep default. The window will then display your defualt IP address which in this case will be 192.168.0.1.

192.168.0.1 IP Login Troubleshooting

In case the admin page does not load, check your connectivity.
Always double-check your connectivity especially if you have a wireless network. Make sure all the cables are in place if you have a wired network. In case you might get 192.168.0.1 refused to connect error into computer network.
Turn your router off and then turn it back again if you are facing connectivity issues.
Always double-check whether all the LEDs on the router are active and green.
Restart your desktop if the problem persists.
For some private IP addresses, access through phones is limited. Hence you may not be able to access the settings panel to configure your router or modem through your phone.
Always ensure you have entered the right IP address. Even a misplaced ‘.’ will lead to error messages.
What to do if authentication required for username and password for 192.168.0.1 ? You can enter user and password as given above.

There are several methods to seek out your IP address. It consists of four numerals. You only have to type a 192.168.0.1 IP address that is used by your router for administration. Each IP address is composed of two parts an identifier of a particular web network, and a device identifier of a network.

D Link Router, Linksys Router, Netgear Router, and TP-Link Router have 192.168.1.1 IP Address.

If you’ve chosen to depart from your network unprotected, you’ll be cautioned that you’re trying to access an unsecured network. In case you have WEP protected your wireless network, you’ll be prompted to put in your password or passphrase. After some time you’re on the net. Now the net is available in two different types. Depending on the time and demand, many users use the web, and the majority of them prefer to use the wireless based internet connection. Need a router If you would like to use Wi-Fi internet as wireless internet, then you want to get a router.

Also Read: How To Reset Router using 192.168.1.1 IP Address

If you can’t access your router with 192.168.0.1 IP address, it can be for few explanations. Don’t forget your router has to be connected by network cable. Every router has its control panel. Therefore it’s important to prepare all key settings. There are several ways of learning about the router. Fortunately, unlike with the password, you don’t need to restore the whole router simply to learn the IP address. Whenever people purchase a new router or modem, it includes a default username and password. On the off possibility, you have both router and modem in your network check out if a router can realize your modem and it’s configured perfectly.

192.168.o.0.1 admin password is sometimes same as 192.168.0.1 but because sometimes people make typing error in ip address but it will also lead to 192.168.0.1/main_login.asp in some routers. There are also typo errors such 192.168.l.0.1 login or 192.168.0.1.1 but it have same login page.

Since if you use your router with the default settings, then there’s a prospect of hacking. The router is only going to work if all the settings and setup are created appropriately. To access the internet page of the Linksys Router you need to use 192.168.0.1. Every router includes default username and password that you can change your requirements. Generally speaking, so long as familiar with the actions described above, you’ve learned how to use a wireless router. An ideal broadband router is a great wireless networking tool which enables us to use internet wirelessly.

Hope this article helps you to connect 192.168.0.1 Router with Windows PC. Comment below if you need any help to customize Router and change Router ID address, Password and default username.

10.0.0.1 Xfinity Comcast Router Login

August 13, 2019 by Sidonia

Do you know what a 10.0.0.1 is? If you are a tech geek with some background in Networking, you might know precisely what these numbers mean, but if you don’t have an idea, fret not, because this article will tell you exactly what it is. 10.0.0.1 is basically a default IP address that is used by several devices. The primary function it has is that it grants you access into the private configuration screens of many routers such as Micronet, Edimax, Siemens and more. While you need to know details such as your modem’s network settings page and login details to make any changes, knowing how to get there is the first step towards tinkering with your network settings. So here’s a look at everything you need to know about 10.0.0.1 and the Login procedure.

Why need 10.0.0.1 ?

The 10.0.0.1 IP address is a unique one because it can be used in more than one functionality. It is a part of the the 24-bit block of private IP addresses, which are typically used for creating local area networks (LANs). You cannot use the public internet to access private IP addresses but this in no way means that they have no value or function.

IP addresses such as 10.0.0.1 are responsible for maintaining the basic architecture of the internet we know and love and prevents it from collapsing. There are approximately over 4 billion IP addresses in the IPv4 communications protocol, and the first regional Internet Registry ran out of addresses way back in April, 2011. Ever since, network administrators and internet providers have been remapping IP addresses onto others and utilising private IP addresses such as 10.0.0.1 as substitutes to sustain the demand for more addresses. With the advent of time, IPv4 will be replaced by the IPv6 but this will still take a little more time. As of now, 25% of all internet users rely on IPv6 to direct their traffic.

Also Check :

What is the Use of 10.0.0.1

Many manufacturers fall back on 10.0.0.0.1 as their default IP Address as it makes it easy to access their device’s configuration page. This is the easiest way to provide user’s with the required admin access to the device. From your modem’s configuration page you can change your settings easily.

10.0.0.1 and 10.0.0.0.1 IP Address Features ?

This IP address directs you to your modem’s configuration page and local settings options from where you can configure and change the settings of your router as per your need or requirement. Given below are some areas or options you can change and configure using the admin panel.

MAC.
DHCP Client, DSL.
IP Qos.
PPPOE.
DNS and Proxy.
LAN, WAN and WLAN settings.
Encryption type
Password and Login credentials
Set-up new network (Dial-Up or DSL)
Set-up static or Advanced DNS
Change your Xfinity or Comcast router login page from 10.0.0.1 Xfinity/10.0.0.1 Comcast to 10.0.4.1 or 10.125.3.1. (Make sure you stay between 10.0.0.0 and 10.255.255.255)
Change your router Network name (SSID)
Set up your custom Parental controls
Increase the safety of your network
Port forwarding for gaming

10.0.0.1 Admin Login – Simple guide

Xfinity users can use 10.0.0.1 to access their admin page and here’s a look at how you can do this.

Connect your router to your device using a cable or wireless network.
Turn both the device and your router on.
Lanuch your preferred web browser.
Enter ‘https://10.0.0.1/ ‘ + URL or IP address in the clipboard into the address bar and press enter.
Find your router’s default username and password from the back of the device.
Feed these credentials in and access the router settings.
Make the changes you require as per your need.
Click ‘Save’ once you are done to complete the process.

As the admin panel gifts you full access to your router, make sure you don’t share your credentials with strangers as they can then use it to make changes to your network system. Increase protection and security by changing your password.

If you don’t know what your default IP address is, then there’s something else than you can do. Type ipconfig and press enter in the command prompt window. A list containing several IP addresses will appear. Look for the one named Default Gateway under Ethernet Adapter as this is the IP address of your router.

Note: 10.0.0.0.1 is the wrong IP address as it was changed to http://10.0.0.1. So, make sure you enter the updated IP address into your address bar.

Common problems you might face in 10.0.0.1 IP Access

Here’s a look at some unforeseen issues which you might have to deal with while trying to gain access into your admin panel.

Default Credentials

If you aren’t sure of what your login credentials are, then go for the default ones because eight out of ten times, this will help you gain access. For doing so, check the back side of your router as this will normally have details regarding your login details. Most router manufacturers would have attached a datasheet with relevant information from where you can pick out your login details.

Denial of Access

Another problem which you might face is denial of access. This can arise as a result of someone having changed the default password to something else which you either don’t know or don’t remember. In this case, you might have to go for restoring your router to factory settings. After resetting your router, you can then go forward and configure a new password as per your liking.

Resetting the Router

To reset the router, look for the reset button on the device itself. In most routers, this button will be beside the power connector but its location may vary according to the type and model of the router. Once you find the reset button, press and hold it for a while, till the LED on the router blinks indicating that reset has been initiated. Doing so will result in the router being reset. After that, you can use the default credentials to gain access to the admin panel and from there, you can go ahead to change the password to something you remember.

10.0.0.1 Default Router Login and Password

Each router manufacturer uses a different default username and password combination. While listing out everything wouldn’t be possible, here are a few of the most commonly used login combinations that you could try out, in case you forgot what your login credentials are.

admin/admin
admin/password
admin/[none]
[none]/admin
[none]/[none]
administrator/password
administrator/[none]
recovery/recovery
root/root
root/[none]

10.0.0.1 IP Login Connection Issues

In most cases, there are three main reasons why people have trouble connecting to 10.0.0.1:

No direct connection: For security reasons, most routers can use the 10.0.0.1 IP address only from a computer they are connected to via an Ethernet cable. While some routers may provide access over a wireless connection, several of them don’t. The best way to solve your connectivity issues would hence, be to buy an Ethernet cable and connect your device to your router directly. Most desktop computers come equipped with an Ethernet port and so the only thing you would require is the cable. If you use a laptop, go for a USB adapter to do the same.
Wrong IP address: Sometimes, even experienced network administrators type in 10.0.0.0.1 instead of 10.0.0.1. Remember that all IPv4 IP addresses contain four numbers and not five. Incase you changed your IP address and don’t remember the new one, then reset your router and access it from the default address to make further changes.
Wrong Credentials: Routers are protected by a password to increase security and prevent strangers from accessing your admin panel. More often than not, we forget what are credentials are. But this shouldn’t cause much of a problem because more times than not, the credentials are the default ones which can be found out easily. If not, you can always reset your router and then access your admin panel.

TP Link Router Login – How to Login into TP Link Router?

August 5, 2019 by Sidonia

TP link has been producing quality routers since long. TP link routers are stable, fast and most importantly, cheap. Netgear, comparatively, is expensive and not affordable to everyone. However, on the other hand, routers by TP link are very affordable and have great price to performance ratio. These routers are fast, reliable and stable. With TP link routers, you’ll be assured with high speed internet connectivity all the time.

Every router comes with some default settings. Users quite often feel the need for changing or altering these settings. Be it the SSID, be it the password or be it the WiFi channel, you can change most of your router’s settings by logging into it. For TP link router login, we’ve explained a step-by-step method below. Before the login method, make sure you’re aware of your login IP. If you don’t know your login IP, you can find it by performing the below mentioned steps.

How to Find TP Link Router Login IP?

TP-Link router can be configured on 192.168.0.1 or 192.168.1.1. You can directly open this IP address and it will prompt setup page for your router.

For Mac users

Go to system preferences which can be found in the apple menu at the top left of your desktop.
Go to network tab > network connection.
Now, click on advance > TCP/IP.
You can now see your default IP address on the right side.

For windows users:-

Go to the bottom left corner of your screen and click on “windows” icon or “start” depending upon the version of windows your system uses.
Now, click on the “gear” icon or the settings icon located right above the shutdown icon.
After clicking on settings icon, select “network and internet”.
Click on “view your network properties” which can be found on the bottom of the page.
In order to know the SSID of your router, look at the right of “WiFI” heading. For the default login IP, look for the heading “default gateway” and the IP address written on the right of the heading is your login IP.

How to Login into TP Link Router?

There are various settings that can be changed by logging into the router’s admin panel. However, you’re always recommended to change only the settings you’re aware of and not just anything else. Router settings are not advised to have fun with. If you alter some unwanted settings, your connectivity and various other factors might be affected.

TP Link Router Login

Here’s the step-by-step method to login into your TP link router login IP:-

Launch your favorite browser.
In the address bar, type your login IP and hit enter.
Now the correct username password combination. If you don’t know your username and password, type “admin” in both the boxes. If “admin” doesn’t work, contacting the customer support is the only option you’re left with.
After typing the correct combination, click on “login” or hot enter. You’ll now successfully be logged into the admin panel of your router.

Most router brands have “admin” as their default username and password. However, you can confirm it by contacting the customer support of your router’s brand along with the model number of your router.

Conclusion

This was a short tutorial on TP link router login through which you can change various settings of your TP link router. Comment below if you face any problem while logging into the router.